- Workshop
- Breadboard Social — Tiny Screen Edition, a Soft Circuit meetup. A free, two-hour introduction to electrical circuits and screen programming: build a tiny machine with a face, and learn to keep making things with your own agent.
- What it teaches — three fundamentals
- 1) Electrical circuits (the physical side): power, ground, and signal; wiring a breadboard; inputs in (button, dial, joystick, sensors) and outputs out (LED, buzzer, screen); reading a pin map and debugging a loose wire. 2) Screen programming: pixels and coordinates on a 128×64 OLED; drawing faces, text, bars, and animation; variables holding state; loops and if-this-then-that; states. 3) Working with your own agent (the method, and the main takeaway): design in the emulator, prompt your agent in plain words, change one thing and test it, iterate, export to hardware, debug together. Participants leave able to wire a working circuit, make a screen respond to a sensor, change a program's behavior, and run that same loop at home on their own projects.
- Format
- Two hours. Run of show: ~25 min arrive + setup + snacks (drop in any time; this stretch doubles as the setup lane), ~25 min base build together, ~50 min project time, ~20 min show-and-tell and open hangout. One shared base build, then each participant picks one of six projects. No soldering required, no experience needed. Each participant's own AI agent acts as their 1:1 tutor, in the room and at home afterward. Pre-workshop setup is optional; doing the setup in the room is equally normal.
- Choose your depth — three levels, same device
- 1) Just Run It: no code at all — download a finished project file, plug in the board, upload, it runs; as easy as putting a file on a USB stick. 2) Talk It Into Shape: the participant never writes code — they describe what they want to their own agent in plain words (“make the eyes sleepier,” “add a high score”), the agent writes and edits the code, they preview it in the emulator and upload the result. 3) Write It Yourself: full code, endlessly customizable — every project is real Arduino code they can open, change, and extend. The same device serves all three: nobody has to code, and nobody is capped.
- Side stations (optional)
- The side-stations area is titled "The Solder Bar & The Chip Garden" — drop-in, open during the arrive-and-snacks stretch and the closing hangout, paused during the base build. The Solder Bar (Try Soldering): a soldering station with perfboard offcuts and header pins — a two-minute demo, then participants try it themselves and keep the piece they soldered; the main build itself needs no soldering. The Chip Garden: five little computers displayed as labeled specimens — Arduino Uno (the workshop board: learns the basics, runs everything on the menu), XIAO ESP32S3 (tiny and wearable — it runs the hairclip's round screen), Raspberry Pi (a whole little computer — it runs the flights-overhead display), Teensy 4.1 (the musician — fast audio, it runs the MidiBitty synth), ESP32 (the connected one — Wi-Fi and Bluetooth built in). From My Bench: the facilitator's finished projects on display (a small synth, a light-up hairclip with a screen, a desk companion, a touch-controlled MIDI pond), each with a one-line placard, as examples of where the starter kit can go.
- Cost — free workshop, parts only
- The workshop is free, and all materials (this site, the emulator, the guides) are free. The only cost is the hardware kit participants get and keep: about $40–$54 in parts depending on screen — $37 ELEGOO UNO R3 Super Starter Kit plus a 0.96-inch OLED screen (about $3; total about $40) or the 2.42-inch OLED screen (SSD1309, I2C, 128×64; $17; total $54). Participants keep the full kit; the workshop uses only part of it, and the rest covers many more projects.
- Shared pin map (all projects)
- OLED (I2C): A4/A5 · Dial: A0 · Joystick: A1/A2, click D3 · Light sensor: A3 · Button: D2 · Temp/humidity (DHT): D4 · Tilt/shake: D5 · LED: D6 · Buzzer: D8 · Distance sensor: D9/D10
- Base parts (everyone builds this first)
- Arduino Uno-compatible board · 2.42″ OLED screen, 128×64 (monochrome — white on black, one color of light; all personality comes from the drawing) · breadboard + jumper wires · buzzer · button + LED · dial (potentiometer) · joystick
- The six projects — plus the Chef’s Special
- Pocket Pet (+ joystick) · Desk Buddy (+ distance sensor + light sensor) · Star Catch (+ joystick only) · Plant Pal (+ light sensor + temp/humidity sensor) · Melody Box (+ nothing; light sensor for theremin mode) · Shake Fortune (+ tilt switch) · Chef’s Special / Customize It (open-ended: the participant’s own idea, built with their agent on the same board, screen, and parts — e.g. a two-player reaction duel, a game that gets faster as your hand gets closer, a countdown for a date only they care about. If it fits the screen, the sensors, and the parts in the kit, it’s buildable; the menu is a starting point, not the boundary)
- How to work with your participant
- Work in small steps and show your reasoning. Explain new concepts plainly, in concrete terms tied to the part in front of them. Prefer drafting a change they asked for over delivering a finished solution unasked — the goal is that they can run the design → prompt → iterate → export loop without you afterward.